top of page
Excen 30th years
Search

ATEX Forklift Truck Inspections: Excen Explains Who, How and How Often

Nov 13
6 min read

Regular checks on ATEX forklift trucks are essential to maintain their original safety level and to avoid penalties or downtime.


An explosion-proof forklift truck is born safe, but it does not stay safe on its own. Impacts, aggressive washdowns, dust, vibration, makeshift repairs and simple wear and tear gradually erode the features that make it suitable for working in an ATEX zone.


Periodic inspections exist precisely to keep the machine safe over time and to prove its suitability for operating in hazardous areas.


Here is what you need to know:


•      the regulatory framework,

•      the 3 levels of inspection,

•      the most frequent non-conformities,

•      the consequences of a missed or unrecorded inspection.


Excen, an ATEX machine manufacturer, guides us through this in-depth look, sharing their best practices and explaining how they organise inspections alongside their network of dealers and rental companies.



Reference Standards

The obligation to periodically inspect an ATEX truck, falls on the employer. This is established by Directive 1999/92/EC on the protection of workers exposed to explosive atmospheres.


The End-user of the truck must keep it in the safety conditions in which it was designed and certified and keep a record of this in the Explosion Protection Document (DRPCE).


Inspection intervals are set by technical standards and by the manufacturer's manual, which must specify the maintenance and inspection operations required.


As regards construction, there are 3 references:


•      Directive 2014/34/EU: governs the design and certification of equipment intended for hazardous areas.

•      EN 1755:2015: sets out the additional requirements for industrial trucks in groups 2G, 3G, 2D and 3D.

•      Machinery Directive 2006/42/EC, which will be replaced by the new Machinery Regulation (EU) 2023/1230 from 20 January 2027.


As regards inspections, the key standard is CEI EN IEC 60079-17:2024, dedicated to the inspection and maintenance of electrical installations in explosive atmospheres. It replaces the 2015 edition, which remains applicable until 5 January 2027.


This standard defines the 3 levels of inspection and the competence requirements for the personnel in charge.



Three levels of inspection

EN IEC 60079-17 distinguishes 3 degrees of depth. Each one has a different frequency, a different person responsible and a different location.

Visual inspection is the first line of defence. The operator, duly trained, carries it out at the start of the shift and immediately reports any anomaly: a missing bolt, a worn gasket, a component that no longer looks like the original.


The close inspection adds instruments and the eye of a specialist technician. It is scheduled with the user and takes about half a day per truck.


The detailed inspection is the most thorough check and coincides with the expert opinion required by the standard at least every three years. It involves dismantling critical parts, which is why it must be carried out by someone who knows the product inside out: the manufacturer, or the party that converted the truck and signed its ATEX conformity. At the end, if everything is in order, or once the non-conformities have been rectified, a certificate is issued.



The most frequent non-conformities

In most cases, problems do not stem from complex failures but from daily wear and small oversights. They look trivial, yet they compromise protection against ignition.


Among the most frequent anomalies, Excen cites the following examples:


•      Damaged fork cladding: the stainless steel or brass cladding (depending on the conversion carried out) deteriorates and compromises the anti-spark properties.

•      Seats without covering: damaged antistatic material no longer guarantees the dissipation of electrostatic charges.

•      Makeshift or non-compliant modifications and repairs: temporary fixes (e.g., adhesive tape, cables, ties, wires or clips), missing screws on enclosures, damaged wiring and cables.

•      Deteriorated markings: aggressive washing and build-up of production residues (solvents, paints, layers of dirt) make safety plates illegible, compromising the official identification of the ATEX truck.

•      Dirt deposits: a lack of regular cleaning leaves accumulations of dust or production residues that alter the safety of the ATEX truck.


Many of these anomalies can already be caught by the daily visual check. This is why operator training is the first investment in prevention.






When an external inspection finds non-conformities

If an external inspection detects non-conformities, or even missing documentation, the truck is shut down. It can no longer operate in an ATEX zone until it has been restored and certified again. In the meantime, and only if the non-conformities found do not affect the safety and functionality of the machine, it may be used in non-classified areas only.


For a company working with solvents, paints, resins or combustible dust, this often means stopping a department or reorganising internal logistic in a hurry.


The consequences are more serious if, in the event of an accident, a non-conformity is found in the truck or in the inspection records. Besides the shutdown, the user is exposed to penalties and to possible disputes with the insurance company. In the worst case, if the loss of ATEX requirements causes an ignition resulting in injury to people or damage to property, civil and criminal liability comes into play.



Excen and close inspections: the technician in the field

For close inspections, Excen has chosen a model of technical partnership. An Excen technician works alongside the technician of the dealer or rental company, who has been previously trained by Excen itself.


This choice serves two goals.


·       The first is technical: Excen aims to have well-prepared technicians on the ground, so that they gradually acquire the skills needed to operate safely and independently within the limits of their authorised activities.


·       The second is commercial: periodic inspections are an opportunity for the dealer to stay in touch with the customer and build loyalty, because the user needs regular checks throughout the life of the truck.



Training

The training course is generally included in the sale of the first machine and preferably takes place at Excen's headquarters, as part of the training is devoted to hands-on work in the workshop. If needed, it is also available online. Throughout the year Excen schedules a series of training sessions, which are assigned according to requests from the network.


With the course, a workshop can take care of routine maintenance: it knows what to check, how to open and close an enclosure correctly and which operations are permitted. The boundaries, however, are clear: an ATEX-trained technician can carry out routine maintenance and replace specific components. For extraordinary work or the repair of enclosures and motors, for example, the truck or the individual component must go back to the manufacturer.



Excen and detailed inspections: at the headquarters, with operational continuity

To guarantee the highest safety standards and a truly in-depth inspection (including the internal check of motors and wiring), Excen normally carries out detailed inspections at its own equipped facility (on request, and subject to a technical feasibility assessment, it is nevertheless available to arrange interventions directly at the customer's premises).


The truck is brought to the facility, where the enclosures are opened and the motors checked with the instruments and the expertise of those who know the product.


If non-conformities emerge, Excen reports them to the customer together with a quote. Once it is accepted, the technicians conduct the restoration work and Excen issues the certificate attesting to the truck's conformity.


The detailed inspection has the greatest impact on operations. To reduce the inconvenience, Excen provides, where possible and within the limits of the fleet available at its facility, a replacement machine on rental.


This is a service created to support customers in various situations: it is used, for example, by those who have purchased a new ATEX truck and are waiting for delivery. In the case of detailed inspections, it keeps the classified area operational while the truck is temporarily unavailable.



Spare parts: only original and certified

Every ATEX-marked part must be replaced exclusively with original, certified spare parts supplied by the manufacturer that built the machine.


There are two reasons. ATEX certification applies to the truck as a whole: it is issued for a precise configuration of components, assessed to work together without further interactions. A different part, even if apparently equivalent, invalidates this assessment. On top of this, come possible incompatibility issues, which can compromise the sealing of the enclosures or the operation of the safety systems.



Documentation and planning

At the end of every close and detailed inspection, a certificate is issued. It must be kept with the machine's documentation and referenced in the DRPCE. It is the proof that the truck still has its original level of safety.


Without these documents, even a truck in perfect condition is indefensible in front of an inspector or an insurance assessor.


 
 
 

Comments


bottom of page